Wisconsin WisDOT DMV CDL General Knowledge Practice Test 5

Test 5 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Wisconsin test.

A country road through dairy farmland with red barns, a typical landscape of Wisconsin
  1. 1. What must a first-time Wisconsin hazmat endorsement applicant complete before the H knowledge test even becomes available to them?

    Show answer

    Answer D: Entry-Level Driver Training

    Wisconsin requires first-time applicants to complete Entry-Level Driver Training before they become eligible to sit for the H knowledge test.

  2. 2. Why should you avoid using your lights to tell a following driver that it is safe to pass you?

    Show answer

    Answer B: You may misjudge the gap and the driver will act on your signal

    The manual warns against signaling others to pass, because the responsibility for a head-on crash then rests on a judgment you could easily get wrong.

  3. 3. What tells a driver when to shift up in a vehicle with a manual transmission?

    Show answer

    Answer C: Engine speed in rpm together with road speed

    Shift points are judged from engine rpm and road speed, using the operating range the manufacturer specifies for that engine.

  4. 4. You are about to slow down sharply on a highway to make a turn into a narrow driveway. How can you warn the drivers behind you?

    Show answer

    Answer C: Tap the brake pedal a few times so the brake lights flash before you slow down

    A few light taps flash the brake lights and give following drivers an early warning that you are about to slow or stop.

  5. 5. A chain rated at 6,600 pounds is fitted with a hook rated at 4,700 pounds. What is the working load limit of that assembly?

    Show answer

    Answer A: 4,700 pounds, the rating of the weakest part

    An assembly is only as strong as its weakest component, so hooks, binders and links all count and the lowest rating governs.

  6. 6. When is tire pressure most accurately compared with the recommended figure?

    Show answer

    Answer B: When the tires are cold, before the vehicle has been driven

    Recommended pressures are cold pressures, so a reading taken before the tires have heated up is the only one that can be compared directly.

  7. 7. You are entering a freeway from a short ramp with a fully loaded trailer. What should you do?

    Show answer

    Answer A: Begin building speed early and wait for a large gap

    A loaded vehicle accelerates slowly, so it needs both a running start and a much larger gap than a car would use.

  8. 8. Part of looking well ahead is planning an out. What does that mean?

    Show answer

    Answer B: Keeping an escape path in mind in case traffic stops suddenly

    Because a heavy vehicle often cannot stop in time, good drivers continuously note where they could steer if the space ahead closes.

  9. 9. How do you get more engine braking from an automatic transmission on a downgrade?

    Show answer

    Answer B: Select a lower range before starting down

    Locking the transmission into a lower range keeps engine speed high enough to hold the vehicle back and spares the service brakes.

  10. 10. Why is a sudden, sharp lane change dangerous in a loaded heavy vehicle?

    Show answer

    Answer D: The vehicle can lean far enough to roll over, especially when the load sits high

    A quick swerve throws the weight of a tall, heavy load sideways, and a rollover can begin before the tires ever slide.

  11. 11. After starting the engine, how quickly should the oil pressure gauge come up to its normal range?

    Show answer

    Answer B: Within a few seconds

    Oil pressure should build within seconds of starting; if it stays low, the engine is not being lubricated and should be shut down.

  12. 12. On a multilane highway, which lane should a heavy vehicle normally use?

    Show answer

    Answer A: The right lane, except to pass or where signs direct otherwise

    Keeping right leaves the faster lanes free and reduces the number of vehicles that have to move around a slower, heavier vehicle.

  13. 13. What is the purpose of blocking placed against cargo on a trailer deck?

    Show answer

    Answer B: To fill the space around the cargo so it cannot slide

    Blocking is shaped to fit snugly against the cargo and fastened to the deck, removing the room the load would need in order to move.

  14. 14. Which parts of total stopping distance can a driver shorten simply by staying alert and looking far ahead?

    Show answer

    Answer B: Perception distance and reaction distance

    Alertness shortens the time spent recognizing a hazard and moving your foot to the pedal; braking distance depends on speed, weight, brakes and the road surface.

  15. 15. How long must the record of a periodic inspection be kept?

    Show answer

    Answer A: Fourteen months

    The periodic inspection report is retained for fourteen months from the date of the report, which covers the full twelve month cycle plus a margin.

  16. 16. Which components on a typical engine are driven by belts that must be checked for wear and tension?

    Show answer

    Answer D: The alternator, the water pump and, on many vehicles, the air compressor

    Belts drive accessories such as the alternator, the water pump and the air compressor, so one failed belt can take out charging, cooling or air supply.

  17. 17. At a rest area you find that the load has shifted although the straps still feel tight. What should you do?

    Show answer

    Answer C: Correct the load before driving on, since a shifted load is no longer secure

    Movement means the securement has already failed once, and a load that has shifted can shift again, so it is put right before the vehicle moves.

  18. 18. On the Interstate System, what is the federal maximum weight allowed on a single axle?

    Show answer

    Answer A: 20,000 pounds

    Federal limits for the Interstate System cap one single axle at 20,000 pounds.

  19. 19. What blood alcohol concentration disqualifies the holder of a commercial driver license who is operating a commercial vehicle?

    Show answer

    Answer D: 0.04 or higher

    Commercial drivers are held to 0.04, half the limit that applies to a driver of a passenger car in the same state.

  20. 20. You have countersteered to correct a rear-wheel skid and the vehicle straightens out. What must you be ready for next?

    Show answer

    Answer D: The vehicle may swing back the other way, so you must steer again to correct it

    A vehicle coming out of a skid tends to overshoot and swing in the opposite direction, and the driver must be ready to countersteer a second time.

  21. 21. You have a part load that fills only a third of a long trailer. How should it be placed?

    Show answer

    Answer C: Spread out and centerd side to side, so the weight sits over the axles

    A part load is spread over as much of the floor as possible and kept centerd, so no axle is overloaded and the vehicle stays balanced from side to side.

  22. 22. Which two CDL endorsements fall outside Wisconsin's military skills test waiver program?

    Show answer

    Answer C: Hazardous materials and school bus

    Wisconsin's military CDL skills test waiver does not extend to the hazardous materials or school bus endorsements.

  23. 23. What do you check about the fire extinguisher during the pre-trip?

    Show answer

    Answer C: That it is securely mounted, charged and that you know how to operate it

    An extinguisher must be held in its bracket, show a charged gauge and be understood by the driver, because a fire leaves no time to learn.

  24. 24. What does a T endorsement authorize a Wisconsin commercial driver to pull?

    Show answer

    Answer B: Double or triple trailers

    Wisconsin's T endorsement authorizes a commercial driver to pull double or triple trailers.

  25. 25. What are you checking when you look at the batteries during the engine compartment inspection?

    Show answer

    Answer D: That they are securely mounted, the connections are tight and free of corrosion, and the caps are in place

    Loose or corroded batteries can fail or short out, so the mount, cables, terminals and vent caps are all part of the check.

  26. 26. What is the correct way to test the parking brake before a trip?

    Show answer

    Answer C: With the parking brake set, put the vehicle in a low gear and gently try to move forward

    A parking brake that holds against a gentle pull in low gear is working; if the vehicle moves, the brake needs adjustment or repair.

  27. 27. Federal rules keep recapped and retreaded tires off the front wheels of which vehicle?

    Show answer

    Answer B: Any bus carrying passengers

    The federal rule names buses: a bus may not run with regrooved, recapped or retreaded tires on its front wheels, because a steer tire failure with passengers aboard takes away steering control.

  28. 28. Where on the road are you most likely to find ice in cold weather?

    Show answer

    Answer B: On bridges, overpasses and shaded stretches, which freeze before the rest of the road

    Bridges and overpasses lose heat from above and below, and shaded areas get no sun, so they ice over first and stay icy longest.

  29. 29. An unblocked article is 15 feet long. What is the minimum number of tiedowns?

    Show answer

    Answer B: Three

    Two tiedowns cover the first 10 feet and one more is added for each further 10 feet or any part of it, so 15 feet needs three.

  30. 30. The combined working load limit of the tiedowns on a load must equal at least what share of the cargo weight?

    Show answer

    Answer C: One half of the cargo weight

    Federal securement rules set the aggregate working load limit at no less than half the weight of the article or group of articles being held.

  31. 31. What must the motor carrier do about a defect listed on a driver vehicle inspection report?

    Show answer

    Answer D: Repair it, or certify that repair is not needed, before the vehicle is dispatched again

    A reported defect must be corrected, or certified as not needing correction, and that certification is what the next driver reads before taking the vehicle.

  32. 32. Why does a driver use pull-ups while backing into a tight space?

    Show answer

    Answer C: To pull forward and start the approach again when the angle is going wrong

    Stopping, pulling ahead and repositioning fixes a bad angle safely, and there is nothing wrong with needing more than one attempt.

  33. 33. An unblocked crate 4 feet long and weighing 900 pounds needs at least how many tiedowns?

    Show answer

    Answer D: One

    An article 5 feet or less in length and 1,100 pounds or less in weight is covered by a minimum of one tiedown.

  34. 34. Where is a dunnage bag used and how does it work?

    Show answer

    Answer D: Between pieces of cargo inside a van, where it is inflated to take up the gap

    A dunnage bag is placed in the void between loads and inflated so the cargo is wedged and cannot move as the vehicle rolls and brakes.

  35. 35. Your drive wheels start to spin and the rear begins to slide while you accelerate on a slick surface. What should you do?

    Show answer

    Answer B: Stop accelerating and, if the vehicle has a manual transmission, push in the clutch

    An acceleration skid ends when the drive wheels stop pushing, so easing off the throttle and disengaging the clutch lets them regain grip.

  36. 36. Why is driving much slower than the rest of the traffic dangerous?

    Show answer

    Answer B: Other drivers must keep passing you, which creates conflicts

    Traffic that has to work its way around you produces lane changes and closing speeds, which is why a large speed difference is itself a hazard.

  37. 37. Within total stopping distance, what exactly is perception distance?

    Show answer

    Answer D: The distance traveled from the moment your eyes see a hazard until your brain identifies it

    Perception distance covers only the time between seeing a hazard and recognizing it as a hazard, before any physical reaction begins.

  38. 38. How does Wisconsin's operator license system separate motorcycle-only privileges from car and commercial privileges?

    Show answer

    Answer D: It issues a distinct license labeled Motorcycle Only for Class M privileges, separate from a Class D card or a Commercial Driver License

    Wisconsin statute requires a license authorizing only Class M vehicles to be labeled Motorcycle Only, kept separate from the Class D regular license and from a CDL for Class A, B or C vehicles.

  39. 39. You have finished a lane change in a vehicle whose turn signal does not cancel by itself. What must you do?

    Show answer

    Answer D: Turn the signal off yourself

    A signal left running tells other drivers you are about to move again, and they may act on that false information.

  40. 40. Rust streaks are running outward from the lug nuts on one wheel. What does this most likely indicate?

    Show answer

    Answer C: The lug nuts may be loose

    Rust trails spreading from the nuts are a classic sign that the nuts have worked loose and the wheel has been moving on the studs.

  41. 41. Why should a driver avoid traveling alongside another vehicle for any length of time?

    Show answer

    Answer D: You lose your escape route and you may be sitting in the other driver blind spot

    Running beside someone leaves nowhere to move if you have to change lanes, and the other driver may not know you are there at all.

  42. 42. Besides the hours when the law requires them, when should headlights be switched on?

    Show answer

    Answer A: Any time visibility is poor, such as in rain, fog or at dusk

    Headlights are used to be seen as much as to see, so they belong on whenever light or weather makes the vehicle harder to spot.

  43. 43. Which of these is NOT on the federal list of parts and accessories the driver must be satisfied are in good working order before driving?

    Show answer

    Answer D: The seat cushion upholstery

    The federal pre-trip rule names brakes, steering, lights and reflectors, tires, horn, wipers, mirrors, coupling devices, wheels and rims, and emergency equipment; seat upholstery is not on that list.

  44. 44. You must drive well below the speed of surrounding traffic, for example when climbing a steep grade with a heavy load. What should you do?

    Show answer

    Answer B: Turn on the four-way flashers to warn following traffic, where state law allows it

    Flashers warn faster traffic that a slow-moving vehicle is ahead, which helps prevent rear-end crashes; some states restrict their use while moving, so check the local rule.

  45. 45. After the first inspection of a trip, how often must cargo securement be checked again?

    Show answer

    Answer D: Every 3 hours or 150 miles or at each change of duty status, whichever happens first

    The load must be re-checked at whichever of those points arrives first, so a loosening tiedown is found long before it fails.

  46. 46. Below 40 mph, what following distance does the standard commercial rule of thumb call for?

    Show answer

    Answer C: One second for every 10 feet of vehicle length

    The base rule allows one second of space for each 10 feet of vehicle length while speed stays under 40 mph.

  47. 47. During the vehicle overview, what should the driver look for on the ground under the vehicle?

    Show answer

    Answer B: Fresh puddles of oil, coolant, grease or fuel

    New stains on the ground are the earliest sign of a leak, so the overview includes a look underneath before anything is opened or started.

  48. 48. You need fuel and the canopy over the pumps is low. What is the safe way to handle the clearance?

    Show answer

    Answer B: Stop and check the height at the entrance and at the way out before committing

    Clearance can differ at the entry, under the canopy and at the exit, and a sloping approach changes the effective height, so both ends have to be checked.

  49. 49. You are backing into a yard where electrical wires cross overhead. What is the main concern?

    Show answer

    Answer C: The wires may hang lower than the top of your vehicle

    Overhead space has to be checked like any other space around the vehicle, because wires and cables are often lower than they look from the cab.

  50. 50. Why must the steering wheel be moved only a small amount at a time while backing?

    Show answer

    Answer B: Because a small turn of the wheel produces a large change at the rear of the vehicle

    In reverse, the effect of the steering is greatly magnified at the back of the vehicle, so a small correction is usually all that is needed.